This post following next on the subject of A Step-by-Step Guide to Installing a Bathtub is exceedingly remarkable. Don't skip it.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is conveniently available, the project can relocate easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will help you install a new bathtub in your restroom if you have already gotten a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall between the bath and also the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub Yourself? Try to leave a short review directly below. We would be interested to see your thoughts about this content. Hoping that you visit us again later on. Kindly set aside a second to share this blog posting if you enjoyed it. I praise you for your time. Please stop by our website back soon.
Browse Our Site